LIGHTING CONTROL

ARIA LITE | ARIA PLUS

THE CONTROL OF LIGHT, IN THE PALM OF YOUR HAND!

Experience lighting that flows as naturally as the air you breathe.

Aria brings the freedom of effortless, intuitive  control to your lighting system. Aria adapts to your needs, providing seamless automation and personalized lighting experiences.

Whether you choose Aria Lite for simple, motion-activated lighting, or Aria Plus for advanced Bluetooth control and scheduling, Aria is available for multiple applications; low bay, high bay, and ceiling mount.

ARIA LITE

ARIA LITE is a standalone lighting control solution that can be configured to different profiles for each fixture, utilize daylight harvesting, and task tuned to optimize occupant comfort and energy efficiency.

ARIA LITE controls are simple fixture installed controls that operate individually without Bluetooth.

Controls
Dimming
Trim Level
Sensitivity
Hold Time
Daylight Harvesting
Standby Dim
Standby Time
NOTES:
  • Each fixture requires one sensor
  • Remote control can program one fixture at a time

ARIA PLUS

ARIA PLUS is a room-based lighting control solution that can be configured to different profiles, utilize daylight harvesting, and task tuned to optimize occupant comfort and energy efficiency.

ARIA PLUS is an easy and affordable gateway-free room-based Bluetooth lighting control solution controllable via mobile app.

Autonomous Lighting Behavior Sensors adjust light levels based on occupancy, task tuning, daylight harvesting, and configurable lighting profiles.
Manual Lighting Behavior The switch turns lights on/off or to preset dim levels. It can also schedule lighting profiles.
Daylight Harvesting Fixture lights are dimmed or turned off in response to daylight.
Occupancy or Vacancy Behavior Configure sensors in a room for manual-on (vacancy switch) or auto-on (occupancy switch).
Energy Savings Depending on occupancy patterns and available natural light, savings may be as high as 65 percent.
Multiple Switches per Room Add switches at each room entry point to control room lights.
Personalize and Reconfigure Customize individual light levels and easily add or remove sensors from a group anytime.
Easy Install Less labor cost compared to wired lighting solutions due to wireless communications between the switch and sensors.
High Bay / Low Bay Application
NOTES:
  • One sensor per fixture
  • Download Keilton application to control the fixture
  • Group 1 can be storage area assign the switch 1 to control the light fixture (up to 100) in this zone
  • Group 2 can be assembly area controlled by switch 2
  • Group 3 the motion sensor “MWS105E” needs “FA102” for Bluetooth connection
  • The three groups can have different lighting schedule
  • Motion sensor and day light harvesting parameters can be different for each group as required
  • Dimming value can be adjusted for each group
Room Sensor
NOTES:
  • One sensor per one power pack (fixture controller)
  • Connect up to 360W total power fixtures to one power pack which are controlled by one sensor
  • Download Keilton application to control the fixture
  • Group 1 can be conference room with downlights and flat panel assign the switch 1 to control the light fixture in this zone
  • Group 2 can be Common Area with downlights controlled by switch 2
  • Group 3 is Offices with one flat panel and motion sensor; stand alone connection
  • The three groups can be controlled by one switch if needed.
  • The three groups can have different lighting schedule
  • Motion sensor and day light harvesting parameters can be different for each group as required
  • Dimming value can be adjusted for each group
NOTES:
  • One sensor can be connected up to 800W total power fixtures (40 of 20W fixtures)
  • CS107S does not need any additional accessory it has built in Bluetooth and output power 800W
  • Download keilton application to control the fixture
  • CS107S is considered as switch; and it is added through the switch menu.
  • Group 1 can be Conference Room with downlights and flat panel assign the switch 1 to control the light fixture in this zone
  • Group 2 can be Common Area with downlights controlled by switch 2
  • Group 3 is Offices with one flat panel and motion sensor; stand alone connection
  • The three groups can have different lighting schedule
  • Motion sensor and day light harvesting parameters can be different for each group as required
  • The dimming option is not available with this sensor
Zone Controller
NOTES:
  • One Zone controller can be connected up to 2400W total power fixtures (100 of 24W fixtures)
  • PPA104S does not need any additional accessory it has built in Bluetooth and output power 2400W
  • Download keilton application to control the fixture
  • PPA104S is considered as Light; and it is added through the Light menu.
  • Area 1, 2 and 3 can be controlled as one light using the zone controller
  • Assign switch 1 to control all the fixture; on/off, dimming and scene
  • The three areas can have same lighting schedule are considered as one group and one light
  • The dimming option is available with this controller